How to Install Attached- Pad Carpets | Home Guides. You can save money by installing attached back carpeting yourself. Because attached- pad carpeting comes in widths of 1. In such cases, securing the edges and middle sections to the floor with double- faced adhesive carpet tape is a fairly simple process.
![Installing Attached Pad Carpet Installing Attached Pad Carpet](http://images.meredith.com/diy/images/2009/04/p_SCF_182_09.jpg)
However, if the room is L- shaped, or if you’re carpeting a large area such as a basement floor, joining sections with invisible seams requires a special technique, patience, and attention to detail. Preparation. Strip off any old carpet. Use a pry bar and hammer to remove the old tack strip from the floor edges, and pull out any remaining nails or staples protruding from the floor; do not remove the shoe molding attached to the bottom of the wall. Next, scrape off any bits of old rubber carpet pad adhering to the floor. Place a small piece if scrap carpeting on the floor against the doors in the surrounding walls.
![Installing Attached Pad Carpet Installing Attached Pad Carpet](http://images.meredith.com/diy/images/2009/04/p_SCF_182_07.jpg)
Use a felt- tip pen to mark the position of a cut line on the face of the doors, in line with the top edge of the carpeting. Remove the first door by tapping out its hinge pins from the bottom with a hammer and a thin Phillips- head screwdriver. Place the door on a pair of trestles, measure and mark the cut line across the width of the door with a metal straightedge, and cut through the line with a portable circular saw. Smooth down the cut edge on the bottom of the door with 9. Remove the remaining doors and repeat this procedure. Sweep off any dust and debris and vacuum the floor thoroughly to complete the preparation.
Seamless Installation. Remove one side of the backing and apply strips of double- faced adhesive carpet tape to the floor around the perimeter of the room. Ensure that the edges butt against the outside walls. Apply additional strips of tape midway across all door thresholds, spanning the width of the opening. Apply additional 4- to 6- foot long strips of tape across the width in the middle section of the floor, spaced evenly at approximately four- foot intervals. Roll out the attached back carpet and position it so that 1 to 3 inches of all the outside edges are folded up against the perimeter walls. Fold half of the carpet back over itself, and remove the backing from all the exposed strips of tape.
![Installing Attached Pad Carpet Installing Attached Pad Carpet](http://88726ab368485283667b-24d38842ee017ede6840e3c1b50a26ef.r27.cf2.rackcdn.com/vault/sale/95535/1_full.jpg)
Start in the middle of the room and smooth the carpeting down onto the strips of tape across the middle, and then out towards the side walls as you work your way across half the length of the room. Next, make sure the attached pads adhere properly to the tape by walking across the edges along the outside walls and tamping the carpeting down with your feet. Fold the other half of the carpeting back over itself and repeat the procedure outlined in the previous step. Crease the carpet at a 9. Force the upward folded edge of carpeting into the bottom corners with the blade of a wide drywall knife. Once you have a distinctive crease along the length and width of the room, use a sharp utility knife to carefully trim the excess off by cutting through the creases.
How to Install Attached-Pad Carpets. Twitter; Pinterest; Reddit; Google+; You can save money by installing attached back carpeting. Roll out the attached back carpet and position it so that 1 to 3 inches of all the.
Cut through the remaining carpeting edge in line with the sides of the door openings. Fold the cut piece into the threshold and trim to size with the aid of the straight edge. Remove the backing from the adhesive strip spanning the doorway and tamp the carpeting down securely.
Place a thin metal carpet edge transition piece over the exposed end of the carpet in the threshold and secure it to the floor with countersunk screws. This step applies only if the carpet ends in the middle of the door jamb and does not butt against existing floor covering. Seams. Secure most of the larger section of carpeting to the floor as described above, but leave a three foot strip adjacent to the seam unattached.
How to Install Attached-Pad Carpet. Carpet that has padding affixed to the back is referred to as attached-pad carpeting, or integral-pad carpeting. This type of carpeting takes less time to install since you do not have to.
Trim the seam edge of the partially laid section if it is not perfectly straight as follows: Place the cutting edge of a special universal carpet cutter 1/4 to 1/2 inch in from the edge of the carpet with the body of the tool protruding into the open space. Use the straightedge as a cutting guide and trim off the ragged edge by sliding the tool along the length of the seam edge. Cut the filler section so that it’s about six inches wider than the remaining gap. Position the filler section next to the partially fitted carpet, with the pattern running in the same direction as the first piece. If there is a distinctive pattern, slide the filler section up or down until the pattern matches up.
![Installing Attached Pad Carpet Installing Attached Pad Carpet](http://rennlist.com/forums/attachments/993-forum/969576d1441296976-993-rs-carpet-installation-guide-20150903_120913.jpg)
CARPET WITH ATTACHED CUSHION By Tom Cartmell. It would be difficult to name each ATTACHED-CUSHION product and show a photograph of each because most carpet manufacturer's private label the backing. In other words, you may see. Anyone installed that carpet that comes with the pad attached? Off Topic. Menard's Around The House Carpet Install. Especially if you install carpet with an attached pad. Category Education. How To Install Carpet Pad - Duration: 8:15.
Lift the side of the fixed piece and slide the edge of the filler piece underneath the fixed section. Adjust if necessary until the pattern is a perfect match. Position the cutting edge of the carpet cutter against the previously trimmed edge of the fixed carpet and slide the tool along the length of the seam to trim the underlying section so that it matches up perfectly. Remove the waste section from underneath the fixed carpet. Slide the filler piece away from the fixed piece and scribe a line on the floor to using the edge as a guide and mark the middle of the joint on the floor.
Fold the fixed section back over itself and apply two strips of double- faced adhesive carpet tape to the floor with their inner edges butting against the floor line. Apply double- faced tape to the perimeter walls surrounding the filler section and attach the edges of the filler section to the tape. Crease the corners with the drywall knife and trim off the surplus as described above. Remove the upward facing backing off the tape along the center strips, together with backing on the remaining strips under the unsecured section of the main piece of carpeting. Work along the seam in 3- foot sections.
Smooth down the remaining unattached section of the fixed piece and apply a thin bead of special seam sealer along the edge of the attached cushion, taking care not to get any sealer on the carpet pile. Once this is done, fold the seam edge of the filler section down against the sealer on the opposite edge, and secure both sides of the seam to the double- faced tape along the joint. Wipe off any sealer adhering to the pile with a damp cloth, and then walk along the seam and tamp it down with your feet. Finally, reinstall the doors by lining up their hinges and securing them with the hinge pins you removed earlier. Things You Will Need.
Pry bar. Hammer. Felt- tip pen. Thin Phillips- head screwdriver. Pair of trestles. Metal straightedge. Circular saw. 90- grit sandpaper. Sanding block. Broom. Vacuum cleaner. Double- faced adhesive carpet tape.
Attached back carpet. Wide drywall knife. Utility knife. Metal carpet edge transition pieces (if required)Countersunk screws (if required)Universal carpet cutter. Tip. Use an old long- necked squeeze bottle such as a ketchup dispenser to apply the seam sealer accurately.
About the Author. After graduating from the University of the Witwatersrand and qualifying as an aircraft engineer, Ian Kelly joined a Kitchen remodeling company and qualified as a Certified Kitchen Designer (CKD). Kelly then established an organization specializing in home improvement, including repair and maintenance of household appliances, garden equipment and lawn mowers. Photo Credits. Jupiterimages/Pixland/Getty Images.